
Nowadays, there are so many products of amt laundry pump in the market and you are wondering to choose a best one.You have searched for amt laundry pump in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings amt laundry pump which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
711 reviews analysed
1. AMT Pump 3201-96 General Purpose Laundry Tray Pump, Aluminum, 1/4 HP, 1 Phase, 115V, 1-1/4" NPT Female Suction & Discharge Ports
2. Saniflo SANICONDENS Gray water pump SN-040: 7" H x 11 1/7" W x 5" D
Description
The SANICONDENS is a small pump that may be used to pump condensate from condensing boilers, HVAC system, water heater systems, etc. The SANICONDENS will pump condensate water up to 15 feet in height and/or 150 feet away from a soil stack. Condensate water has the potential to cause property damage or even create health hazards that can affect indoor air quality. Many times, the condensate is not able to drain through gravity to an existing drain line. This is the reason a condensate pump is essential to many residential and commercial applications. The inside of the SANICONDENS comprises of a float mechanism, which starts and stops the unit, and the motor, which drives the pump. When the water enters the SANICONDENS, it activates the float mechanism, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum. Water enters the chamber and is pumped away into the sanitary sewer. The unit pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the float deactivates the unit until water enters the unit again. A normal operating cycle for the SANICONDENS can be as short as 2 – 10 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal. The discharge connection on the top of the unit comes equipped with a non-return valve, which prevents back flow into the unit. It is also highly recommended for the condensate pump to be connected to a Ground Fault Interrupter (GFI) circuit. The small, powerful pumping unit can be floor or wall mounted. It comes with an auxiliary external overflow switch that will shut down the appliance or alert the consumer in the event of overflow. It also includes all necessary hardware for ease of installation; 20 Ft of vinyl tubing, inlet adapter, discharge adapter
3. Zoeller 105-0001 Sump Pump 12.50 x 14.50 x 14.50 inches 19 Pound
Description
Product Description
105-0001 Features: -Drain pump package. -No filters to clog or maintain. -P-trap can be installed internally for compact installations. -Allows drainage from areas where gravity is not present. -Can be used with dishwashers, laundry trays and garbage disposals. -1 Year warranty. -Dimensions: 12.5" H x 14.5" W.
From the Manufacturer
Removes water from areas where gravity flow is not available. Applications include laundry tray pump, wet bar sink, lavatory, air conditioning condensate and dehumidifier water removal. Can also be used in conjunction with dishwashers and garbage disposal applications. Glass-filled, polypropylene base with built in strainer on M53. Passes laundry lint and 1/2″ spherical solids
4. Little Giant WRSC-6 Compact Drainosaur Tank and Pump Combination System
Description
Product description
WRSC-6 Hz / Volts / Cord: 60 Hz / 115 Volts / 8′ Cord Features: -Completely assembled and ready to be installed.-Intermittent Liquid Temp. up to 125 F.-Epoxy coated cast iron housing.-Polycarbonate Cover.-Polypropylene Volute.-Nylon Impeller.-Carbon/Ceramic Shaft Seal.-Upper and lower bearings.-Automatic Operation.-Diaphragm switch Activator.-Switch on – 4-7” / Switch off – 1-3”.-HP: 1/3.-Hz: 50/60 or 60.-Tank Size: 3.5 Gallons.-GPM at 5′ of Head: 45′.-Maximum Head at 18′.-FNPT Top Vent Port: 2”.-Top Discharge Port: 1.5”.-Side Discharge Port: 1.5”.
From the Manufacturer
WRS Series, a convenient smaller sized tank and pump combo, is ideal for impractical gravity drainage areas such as under sinks and laundry trays. Includes: tank and pump with 8-Feet power cord. 1/3 Horsepower, 46 GPM at 5-Feet head, 115 V, 60 Hz.
5. LTP-1 Hartell Laundry Tray Pump, W/2 Gallon Reservoir, 115 Volt, 1/4 HP 1-1/2" Inlet 1" Outlet
Description
LTP-1 Hartell Laundry Tray Pump, W/2 Gallon Reservoir, 115 Volt, 1/4 HP 1-1/2″ Inlet 1″ Outlet
6. Flotec FPUS1860A Utility Sink Pump System
Description
1/4 HP Utility Sink Pump has a maximum discharge flow of 2,000 GPH and is ideal for basement laundry sinks, wet bars and utility sinks. The pump can be used for sinks where a gravity drain line is not available and the stainless-steel pump housing offers durability. The pump comes with an elbow and strainer for the sink drain, an adapter, check valve, O-ring and gasket seal for easy installation. Maximum discharge flow of 2,000 GPH Use for pumping drainage water without an in-ground basin Ideal for basement laundry sinks, wet bars and utility sinks where a gravity drain line is not available Stainless-steel pump housing offers durability No connection to main-stack vent required Includes an elbow and strainer for the sink drain, an adapter, check valve, O-ring and gasket seal for easy installation
7. AMT Pump 316A-95 Sewage & Trash Pump, Cast Iron, 3 HP, 3 Phase, 230-460V, Curve A, 2" NPT Female Suction & Discharge Ports
Feature
- Clog-resistant impeller handles semi-solids up to 1″ diameter for use in waste water and chemical processing
- 3 hp, 3 phase, TEFC, 230/460V, 8/4 amp motor
- Cast iron with Viton/silicon carbide mechanical seal and Viton O-ring
- Maximum operating temperature 180 degrees F
- 2″ female NPT suction port, 2″ female NPT discharge port
Description
This AMT 316A-95 engine-driven sewage and trash pump has a cast iron housing, a 3 hp, 3 phase, 230/460V TEFC electric motor, and 2″ female NPT suction and discharge ports. This pump has A curve performance with a 150 gallons per minute (gpm) maximum flow rate and 62 feet maximum vertical lift at 3,450 RPM. The pump is self-priming to 20 vertical feet (after initial fill) with its built-in check valve, and its clog-resistant impeller handles fluids containing up to 15 percent semi-solids. The pump housing has Viton (FKM, fluoroelastomer)/silicon carbide mechanical seals and Viton O-rings for corrosion resistance. The housing’s double volute chamber reduces radial load on the impeller, and both the volute and impeller are replaceable with the removal of four bolts. The motor enclosure is totally enclosed, fan cooled (TEFC) for protection from dust and indirect water spray and complies with National Electrical Manufacturers Association (NEMA) 56J standard for mounting dimensions. This portable pump is suitable for use in applications such as in sewage treatment, canneries, chemical processing, wineries, tanneries, meat packing, breweries, pulp, wood chips, sludge and slime, and waste water.
Specifications
Motor | 3 hp, 230/460V, 8/4 amp, 3 phase, TEFC |
Pump | Centrifugal self-priming with dual volute |
Maximum flow rate | 150 gpm |
Impeller | Stainless steel self-cleaning, semi-open |
Suction port | 2″ NPT |
Discharge port | 2″ NPT |
Maximum operating temperature | 180 degrees F |
Standards met | NEMA 56J |
Maximum solids handling | 1″, 15 percent of total volume |
Dimensions* | 19.9/50.5** x 9.3/23.6** x 8.8/22.3 (L x W x H) inches/centimeters |
* L is length, the horizontal distance from front to back; W is width, the horizontal distance from left to right; H is height, the vertical distance from lowest to highest point
**This measurement may vary due to motor manufacturer’s specifications
Pumps use mechanical action to move liquids, gases, or slurries (solids suspended in a liquid or gas). The mechanical action is categorized as either positive displacement (PD) or kinetic. PD pumps capture and release discrete amounts of flow into a chamber and then force it out. Some examples of PD pumps are fuel and oil pumps in cars, pumps in hydraulic systems, and bicycle pumps. Kinetic pumps move liquids, gases, or slurries by transferring energy from the pump’s movement to the flow. They use an impeller to draw the flow in, add energy to the flow, and move it through a volute (a spiral funnel through which the flow moves), and into the system. Some examples of kinetic pumps include centrifugal (the most common pump in industrial applications), in-line pumps, sump pumps, and suction pumps. Energy sources for all types of pumps include wind power, manual operation, electricity, and gasoline or diesel fuel.
American Machine and Tool (AMT) manufactures centrifugal and diaphragm pumps. The company is headquartered in Royersford, PA.
8. AMT Pump 388F-97 Inline Centrifugal Pump, Bronze, 1/2 HP, 1 Phase, 115/230V, Curve A, 1-1/2" NPT Female Suction & Discharge Ports
Feature
- Self-cleaning impeller handles semi-solids up to 1/8″ for use in liquid transfer and recirculation applications
- 1/2 hp, 1 phase, TEFC, 115/230V, 8/4 amp motor
- Bronze with buna-n mechanical seal and O-ring
- Not self-priming, requires flooded suction
- 1-1/2″ female NPT suction port, 1-1/2″ female NPT discharge port
Description
This AMT 388F-97 bronze inline centrifugal pump has a 1/2 hp, 115/230V, 1 phase electric motor and 1-1/2″ female NPT suction and discharge ports. This pump has A curve performance with a 50 gallons per minute (gpm) maximum flow rate and 48 feet maximum vertical lift at 3,450 RPM. The pump housing has a pull-from-rear design for servicing without disturbing pump housing connections, a stainless steel self-cleaning impeller that handles semi-solids up to 1/8″ diameter, and buna-n mechanical seal and O-ring. The motor enclosure is TEFC (totally enclosed, fan cooled) for protection from dust and indirect water spray and complies with National Electrical Manufacturers Association (NEMA) 56J standard for mounting dimensions. This portable pump requires flooded suction for priming and is suitable for use in applications such as liquid transfer, recirculation, and wash down.
Specifications
Motor | 1/2 hp, 115/230V, 8/4 amp, 1 phase, TEFC |
Pump | Centrifugal, not self-priming |
Maximum flow rate | 50 gpm |
Impeller | Self-cleaning, semi-open |
Suction port | 1-1/2″ NPT |
Discharge port | 1-1/2″ NPT |
Maximum operating temperature | 180 degrees F |
Standards met | NEMA 56J |
Dimensions* | 13/33** x 8.9/22.6** x 8.7/22 (L x W x H) inches/centimeters |
* L is length, the horizontal distance from front to back; W is width, the horizontal distance from left to right; H is height, the vertical distance from lowest to highest point
**This measurement may vary due to motor manufacturer’s specifications
Pumps use mechanical action to move liquids, gases, or slurries (solids suspended in a liquid or gas). The mechanical action is categorized as either positive displacement (PD) or kinetic. PD pumps capture and release discrete amounts of flow into a chamber and then force it out. Some examples of PD pumps are fuel and oil pumps in cars, pumps in hydraulic systems, and bicycle pumps. Kinetic pumps move liquids, gases, or slurries by transferring energy from the pump’s movement to the flow. They use an impeller to draw the flow in, add energy to the flow, and move it through a volute (a spiral funnel through which the flow moves), and into the system. Some examples of kinetic pumps include centrifugal (the most common pump in industrial applications), in-line pumps, sump pumps, and suction pumps. Energy sources for all types of pumps include wind power, manual operation, electricity, and gasoline or diesel fuel.
American Machine and Tool (AMT) manufactures centrifugal and diaphragm pumps. The company is headquartered in Royersford, PA.
9. AMT Pump 2874-95 Self-Priming Centrifugal Pump, Cast Iron, 3 HP, 3 Phase, 208-230/460 V, Curve A, 3" NPT Female Suction & Discharge Ports
Feature
- Clog-resistant impeller handles semi-solids up to 3/8″ diameter for use in waste water drainage and processing
- Built-in flapper/check valve permits self-priming to 20 feet
- Cast iron with buna-n mechanical seal and O-ring
- Maximum operating temperature 180 degrees F
- 3″ female NPT suction port, 3″ female NPT discharge port
Description
This AMT self-priming centrifugal pump has a cast iron housing and 3″ female NPT suction and discharge ports. The pump is self-priming to 20 vertical feet (after initial fill) with its built-in check valve, and its clog-resistant impeller handles semi-solids up to 3/8″ diameter. The pump housing has buna-n mechanical seal and O-ring, a fill and drain plug for easy servicing, and a double volute chamber for reduced radial load on the impeller. The motor enclosure is TEFC (totally enclosed, fan cooled) for protection from dust and indirect water spray and complies with National Electrical Manufacturers Association (NEMA) 56J standard for mounting dimensions. This pump is suitable for use in applications such as wastewater processing and treatment.
Specifications
Motor | 3 to 7.5 hp, TEFC |
Pump | Centrifugal self-priming with dual volute |
Maximum flow rate | Ranges from 250 to 375 gpm |
Impeller | Stainless steel self-cleaning, semi-open |
Suction port | 3″ NPT |
Discharge port | 3″ NPT |
Maximum operating temperature | 180 degrees F |
Maximum solids handling | 3/8″ |
Standards met | NEMA 56J |
Pumps use mechanical action to move liquids, gases, or slurries (solids suspended in a liquid or gas). The mechanical action is categorized as either positive displacement (PD) or kinetic. PD pumps capture and release discrete amounts of flow into a chamber and then force it out. Some examples of PD pumps are fuel and oil pumps in cars, pumps in hydraulic systems, and bicycle pumps. Kinetic pumps move liquids, gases, or slurries by transferring energy from the pump’s movement to the flow. They use an impeller to draw the flow in, add energy to the flow, and move it through a volute (a spiral funnel through which the flow moves), and into the system. Some examples of kinetic pumps include centrifugal (the most common pump in industrial applications), in-line pumps, sump pumps, and suction pumps. Energy sources for all types of pumps include wind power, manual operation, electricity, and gasoline or diesel fuel.
American Machine and Tool (AMT) manufactures centrifugal and diaphragm pumps. The company is headquartered in Royersford, PA.
Conclusion
By our suggestions above, we hope that you can found Amt Laundry Pump for you.Please don’t forget to share your experience by comment in this post. Thank you!